Support / The scan does not find my camera, but its manual gives an rtsp:// address.
How to add an IP camera using an RTSP URL
Last updated:
In short
An RTSP URL tells ViewTile where to request a camera’s video. Try Camera address for ONVIF first; use Stream address when the device provides an RTSP stream but no usable ONVIF connection. Enter the username and password in their own fields, not in the URL.
Choose how to add the camera
ONVIF lets ViewTile ask a camera about its streams, clock and available controls. An RTSP URL provides a direct route to video, without that setup conversation.
ViewTile has not been tested with the brands’ cameras listed here. The patterns below are according to Hikvision’s, Dahua’s, Reolink’s and TP-Link’s documentation (read 16 November 2026). They are starting points to compare with your device’s manual, not a promise about a particular model.
For a camera that offers ONVIF, choose Camera address and enter its IP address, ONVIF port, username and password. The ONVIF port is not necessarily the RTSP port. If ONVIF is unavailable, choose Stream address instead. An http:// address for an MJPEG camera can also be entered there.
Understand the RTSP URL format
A typical address looks like rtsp://192.168.1.50:554/Streaming/channels/101.
rtsp://is the scheme. It identifies the streaming protocol.192.168.1.50is an example IP address. Replace it with the camera’s actual local address, or the recorder’s address when requesting a recorder channel.:554selects the RTSP port. Port 554 appears as the default in the four brands’ documentation below, but the device’s configured port wins./Streaming/channels/101is the path. It selects a stream and sometimes a recorder channel. Copy its spelling and capitalization from the relevant documentation.- A question mark starts parameters on some cameras. In Dahua’s pattern,
channel=1&subtype=0selects the channel and stream.
Vendor examples often put username:password@ before the IP address. Leave that part out in ViewTile and use the separate login fields. The examples below deliberately contain no credentials.
Common camera stream addresses
Replace IP with the device’s address. Each complete example uses port 554; replace that number if your camera has a different RTSP port.
| Brand or format | Main stream | Substream |
|---|---|---|
| Hikvision | rtsp://IP:554/Streaming/channels/101 |
rtsp://IP:554/Streaming/channels/102 |
| Dahua | rtsp://IP:554/cam/realmonitor?channel=1&subtype=0 |
rtsp://IP:554/cam/realmonitor?channel=1&subtype=1 |
| Reolink, current format | rtsp://IP:554/Preview_01_main |
rtsp://IP:554/Preview_01_sub |
| Reolink, older codec-prefixed format | rtsp://IP:554/h264Preview_01_main |
rtsp://IP:554/h264Preview_01_sub |
| Tapo | rtsp://IP:554/stream1 |
rtsp://IP:554/stream2 |
| Axis | rtsp://IP/axis-media/media.amp |
Add ?resolution=640x360 |
Hikvision’s RTSP instructions describe the 01 main and 02 substream endings. Dahua’s RTSP instructions describe channels starting at 1 and subtype 0 for main, 1 for the first extra stream and 2 for the second.
Reolink’s current RTSP instructions use Preview_. Try that form first. The older codec-prefixed spelling remains in vendor documentation; Reolink’s RTSP explanation also gives h265Preview_01_main for certain H.265 cameras, alongside h264Preview_01_sub. Check the camera’s encoding before choosing that fallback.
TP-Link’s camera instructions give Tapo’s stream1 and stream2 paths and require a separate camera account. These paths do not mean every Tapo device offers RTSP. The Axis row is retained from the makers’ documentation check of 22 September 2026; it was not rechecked for this update.
Choose the recorder channel
Use the recorder’s IP address when the stream comes from the recorder. Changing the IP to a camera hidden behind it does not necessarily make that camera reachable from your phone.
For Hikvision, the stream ID is the channel number multiplied by 100, plus the stream type: 1 for main or 2 for sub. Channel 2 main is 201; channel 3 sub is 302. Hybrid recorders may number digital channels after their analog channels.
For Dahua, change channel=1 to the recorder channel you need and retain the appropriate subtype. Confirm the recorder’s channel mapping. Reolink’s documented channel 2 example uses Preview_02_main and the recorder’s credentials. See Cameras behind a recorder if the channel is unclear.
Enter the address in ViewTile
- From the empty camera wall, tap Add a camera.
- On the Local Network explanation screen, choose Find cameras to scan, or Type the camera address instead to enter an address.
- Use Camera address first if ONVIF is available. Enter its service port and run the connection test.
- Otherwise, choose Stream address. Pasting an
rtsp://link switches to that mode. - Enter the username and password in their separate fields. Check the IP, port and complete path before connecting.
A camera added through Stream address provides video only. It has no pan and tilt, picture settings, clock check, recordings or diagnostics beyond playback. It also has no discovered alternate stream to switch to automatically. Choose the smaller stream’s URL if that is what you need for the wall.
When the address does not play
No video from this camera means no video arrived after three attempts over TCP and then UDP. For a stream address, ViewTile points to the address, path, password or local network as the likely cause.
Compare the entire address with the camera’s own settings or manual, especially the path after the host. Use the password assigned to the stream or camera account. Enable RTSP or correct its port on the camera or recorder, not in ViewTile. Check network isolation or blocked traffic on the router.
A camera still booting may answer before it can send video. A long keyframe interval can also leave a black picture after reconnecting. See IP camera found but no picture and Main stream vs substream for the next checks.

