Support / The scan finishes and finds nothing
ONVIF camera not found: what to check
Last updated:
In short
An ONVIF camera not detected by the scan may still connect when you enter its address. Start with the network your phone is using, then check whether the router separates it from the cameras. An empty scan does not establish that a camera is broken or unsupported.
Check these in order
-
Check which Wi-Fi network your phone is using. Look at the network name in the phone’s Wi-Fi settings. A guest network or a second network in the same building can put the phone somewhere the cameras cannot be reached. Join the network the cameras use, then run Find cameras again. A wired camera can share a network with a phone on Wi-Fi: the important part is whether the router allows them to communicate, rather than whether both use wireless connections.
-
Check whether the cameras are on a separate VLAN. An installer may have placed the cameras on their own network segment, called a VLAN. The scan searches the local subnet, so cameras on another segment may not appear. Ask whoever manages the network for a camera’s IP address and ONVIF port. Enter those using Camera address. A direct connection may work if the router routes traffic between the networks. If it does not, the routing or firewall needs attention on the router, not in ViewTile.
-
Check the router’s device isolation settings. Look for settings called client isolation or AP isolation, particularly on guest Wi-Fi. These can prevent a phone from reaching a camera even when the network names look right. The router must allow communication between the devices for ViewTile to connect. On a managed network, ask the administrator to check this. Repeating the scan cannot get around isolation or a firewall rule that blocks the connection.
-
Try the address of a camera that does not announce itself. Some cameras do not announce themselves, and discovery may be disabled on others. ViewTile also checks addresses directly during its scan, but it cannot cover every possible service port. From the camera wall’s empty state, choose Add a camera, then Type the camera address instead. Use Camera address for the camera’s IP address, ONVIF port, username and password. If the connection test succeeds, the camera was reachable even though discovery did not find it.
-
Confirm that the camera has power and the expected address. Check the camera’s power connection and whether it has finished starting up. Confirm its current IP address using its own settings or the router’s device list. An old address may now belong to another device, or the camera may have joined a different network. Correcting power, cabling or the camera’s network connection happens outside ViewTile. If the camera sits behind a recorder, see Cameras behind a recorder for that setup.
-
Check local network permission on iPhone or iPad. Open Settings > Privacy & Security > Local Network and make sure ViewTile is allowed. Without that permission, the app cannot access cameras on the local network. Return to ViewTile and repeat the scan after allowing access. This is a device permission, separate from the camera’s username and password. See Local network permission on iPhone if you need help finding the setting.
-
Let the scan finish, then use Search deeper if needed. Find cameras sends a WS-Discovery probe, listens for SSDP announcements, checks web ports 80, 8000 and 8080 across the subnet, and checks for a video stream on port 554. Search deeper repeats the search across every address using ports 80, 8000, 8080, 8081, 8090, 8899, 554 and 8554. It takes about a minute. A camera using another port needs its address entered manually. If you stopped the scan early, an unfinished search does not tell you that nothing is reachable.
-
Read the first failed connection test step. When you enter an address, Camera reachable and Camera speaks ONVIF help distinguish network trouble from a camera service problem. Host unreachable points to the address, power or network route. Port closed means the device answered but nothing listens on that port. Not an ONVIF device means an HTTP service answered without an ONVIF response. Check the camera’s ONVIF settings and port, which can differ from its web page port. These fixes belong on the camera or router.
If discovery still finds nothing
If the camera offers a documented RTSP address, try Adding a camera by its stream address. This provides video only, without ONVIF controls or diagnostics beyond playback. A brand name alone does not establish that a particular model exposes ONVIF or RTSP.
ViewTile works on the local network only. If you are outside the building, see Watching from outside the building.

